Search results for "Maximum power point tracking"

Power tracking with maximum efficiency for wireless charging of E-bikes

2014

Wireless charging techniques, based on Inductive Power Transfer (IPT), are attractive for Electric Vehicles (EV), due to benefits such as convenience and safety. An accurate valuation of the maximum achievable efficiency in an IPT system is extremely unlikely due to the high sensitivity to parasitic elements variations. Therefore, an “on site” procedure of power efficiency characterization is useful to get a precise description of the efficiency curve and obtain the actual maximum efficiency. In this paper, a power tracking algorithm aiming at efficiency maximization is proposed for a Wireless Charging system. The algorithm aims at finding the maximum power transfer efficiency with respect …

Numerical Analysis of Medium Scale PV Plants and Their Power-Flow Control System With a Simple Three Phase Inverter

2012

This paper presents a mathematical analysis of a medium scale Photovoltaic (PV) power generation system connected to the distribution network and of its control system, in which the conversion stage is unique thanks to the absence of a boost chopper. Boost choppers are usually used as actuator for maximum power point tracking (MPPT). The conducted analysis leads to the conclusion that the used inverter presents two degrees of freedom that can be easily exploited in a control system in which the inverter simultaneously realizes the interconnection to the grid and at the same time realizes the MPPT control. The structure of the control system is then presented, discussed and then validated by…

Sensorless small wind turbine with a sliding-mode observer for water heating applications

2015

Water heating applications consume a considerable portion of electricity demand in most of countries. Small wind turbines are one of attractive alternatives for grid electricity based water heating systems. Wind energy can be converted to heat energy in a high efficient manner. However it is essential that wind turbine based water heating systems should be economical and reliable. Maximum power point tracking algorithm of most of available wind turbines requires information from a wind speed sensor and a rotor speed sensor which reduces the reliability of the system. In this paper, the proposed 5 kW wind turbine does not require external wind speed sensors and rotor speed sensors. The syste…

Performance evaluation of a multisource renewable power converter prototype

2014

Performance of grid-connected PV system in Southern Norway

2015

This paper presents performance results from one of the first grid-connected photovoltaic (PV) systems in Norway. The 45 kWp system is mounted on top of a flat roof at the headquarters of a local utility company, Agder Energi, in the coastal town of Kristiansand. The system consists mainly of multi-crystalline silicon modules, with one thin film array. The system has been in operation since May 2011 and is instrumented for research and monitoring purposes. Data recorded include global and diffuse horizontal irradiation, tilted irradiation and other weather parameters, PV module temperatures, DC and AC current and voltage for three arrays, in addition to inverter power data and voltage quali…

Development details and performance assessment of a Wind Turbine Emulator

2016

This paper describes an experimental platform to emulate the static and dynamic behavior of real Wind Energy Conversion Systems (WECS). The Wind Turbine Emulator (WTE) consists of two coupled 1.5 kW squirrel-cage induction machines. The WTE calculations are performed on a PC and a DSP, both connected via USB. The total torque applied to the WTE motor is the difference of the scaled wind mechanical torque calculated on the PC, and the turbine inertia torque calculated on the DSP. An improved WTE shaft speed derivative has been used for the inertia torque calculation, which provides better results in terms of attenuation of the high-frequency harmonics present in the generator speed acquisiti…

A simple and accurate model of photovoltaic modules for power system design

2014

Sliding-mode observer based sensor-less control of a small wind energy conversion system

2015

Small wind turbines are becoming an attractive solution for household applications. These micro generation units can be used as standalone applications or grid connected applications. However to get the full potential benefits of these wind turbines, systems should be low cost and reliable. Introducing the wind speed and rotor speed sensors at the generator shaft may reduce the reliability of small wind turbines. In this study, a grid connected sensor-less 5 kW small wind energy conversion system has been studied. The maximum power point tracking method of the wind turbine is totally independent from wind speed and rotor speed measurements. Optimum rotor speed and actual rotor speed are est…

Economic benefits of the use of a PV plants reconfiguration systems

2015

This paper shows the economic convenience of the application of a reconfiguration system for photovoltaic plants, considering the incentives system in different Countries. The reconfiguration is an alternative to the Distributed Maximum Power Point Tracking, DMPPT, technique used to overcome the mismatch problem in Photovoltaic, PV, plants. The reconfiguration techniques employ a microprocessor-based system that modifies the layout of the PV plant by physically changing the connections among modules. After having presented the working principle of the PV reconfiguration system allowing the improvement of the efficiency of the same plant and the relevant installation, the main strength and w…

Design of a solar-battery-thermoelectric power converter prototype

2015

In this paper a multisource renewable energy system for high-current applications is proposed. The power architecture is based on a multi-input power converter including control and reconfiguration subsystems. Independently of the type of connected renewable sources, a proper control of the output DC voltage bus is provided as well as a proper control on the operating point of each renewable source to achieve the maximum power transfer. A 48V thermoelectric-photovoltaic-battery system in a three input configuration is designed. Three interacting feedback networks are implemented: the outer loop which controls the output voltage and as many inner loops as connected renewable sources to achie…